Friday, March 16, 2012

Canned Food Storage

 We have been looking for a way to store our canned food that takes up less space than just putting them on a shelf.  We found inspiration on Pinterest and built our own self-rotating racks!  With just a piece of plywood and some 1x3s and some 1x2s.  Some L brackets and lots of screws we built this!!  We made sure that the cans that we wanted to put here fit in each row.  At the bottom of each row, we put this wedge piece.
 And on the wedge we screwed in an L bracket.  That way the can doesn't fall out on it's own.
 We screwed two boards with an angled cut at the top to the wall and the rack had boards with opposite angle cuts on the back. 
 Here is the first rack.  The end spot was not big enough for a can, so Toby just put two shelves and we are stacking tuna there!
 And here are both!  I love them!!!
UPDATE We had a request for more information on the canned food rack that we posted a couple of months ago.  Since it's hanging on the wall, it's kind of hard to get pictures, so I'll try to explain what I did.

If I was building it again, I'd use very thin plywood (1/4" or thinner) for the pieces that go on the front of the rack, instead of 1"x2".   They just have to be strong enough to prevent the cans from falling forward and using thinner wood would make it lighter.

The angled piece at the bottom of each row of cans was just cut from a 2x4.  My saw blade wasn't quite large enough to cut all the way to the top of a 2x4 so I cut off about 1/2" from the top of the 2x4, see Fig 1.



Then I cut the 2x4 lengthwise in half at an angle.  I angled my saw blade at around 25 deg to cut through the bottom corner and angle up to come out at the opposite top corner see Fig 2.

Once I had it cut in half at an angle, I cut the piece into 2-3" wide triangles.  These are what I attached to the bottom of each row of cans.  I glued and then drilled a countersunk hole in the angled pieces at the bottom of where the cans will go.  I then put a screw in the countersunk hole and made sure the head didn't come above the surface of the wood.  That gave me a sturdy and secure surface to attach the angle bracket.

The boards that hold it to the wall were about 1/2" thick plywood.  I cut them into strips about 6" wide.  Then, I made a 45deg cut lengthwise down the center of the strip, producing 2 3" wide pieces.  I then repeated until I had 4 3" pieces for each rack.  I marked the two halves so I knew which pieces went together, in case there was any variation in the 45deg cut.  Find the studs in your wall and mark them.  While you could use drywall anchors I think screwing the boards to the studs is much more secure. You attach two separate piece to the wall, with the cut side pointing upward and the high side of the 45deg cut away from the wall.  This creates a pocket against the wall.  If you attach it backward, the cut will slope away from the wall and the food storage rack will fall off.  I then set the other two pieces into their matching pieces on the wall.  With a second person, we then held the rack up against the 4 boards on the wall.  Quickly drive 2 screws through the rack into each of the unattached pieces.  This will connect them to the rack and make sure they match up with the 2 pieces on the wall.  I then screwed screws through the rack into both the rack mounted board and the wall mounted board to give it more strength and prevent it from moving.

53 comments:

  1. So cool!!! You guys are so smart!

    ReplyDelete
  2. We absolutely LOVE it! What an awesome job.

    Love & miss you,
    Juliana

    ReplyDelete
  3. Good job. we love Pintrest ideas.

    ReplyDelete
  4. Could you please post pics of the angle cuts on the boards on the wall and the other angle cuts on the boards on the storage unit? I would love to copy this for my can food storage.

    ReplyDelete
  5. I love this rack! Thanks for sharing. I've shared it with my readers on my site.

    ReplyDelete
  6. The method you're using to attach them to the wall is called "cleats". Here is a video showing how to do it: http://www.ronhazelton.com/projects/how_to_hang_pictures_using_wood_cleats

    They're hanging a picture, but it's the same idea. We used this method to hang our kitchen cabinets, that way you can adjust the spacing before you attach them to the wall. Works great for alot of different things.

    ReplyDelete
    Replies
    1. Love the idea for hanging cabinets with the use of cleats!

      Delete
  7. I love this idea..I want to make it. Thanks for sharing!

    ReplyDelete
  8. This is a great idea. I saw the link on Homestead Survival that sent me over here. I can't wait to get my husband to make me some of these.

    ReplyDelete
  9. How exciting! I have seriously enjoyed reading this article. You guys have built a excellent community!
    Canned Foods Market

    ReplyDelete
  10. Nice use of French cleats. Or do we call them "Freedom Cleats" now?

    ReplyDelete
  11. I would definitely buy one if u ever sold them..

    ReplyDelete
  12. Will you make them to sell?
    I would like three.
    Mel bosek

    ReplyDelete
  13. Please let me know if you will make them to sell.
    I use progreso soups, spaghetti sauce , Campbell. And small tomatoes paste cans.
    Tuna fish and kipper snacks cans too.

    Look forward to hearing from you.

    ReplyDelete
  14. Wow...Many Thanks!

    Just what we were looking for.

    ReplyDelete
  15. Ok...when y'all come to make me one?... Lol... Y'all did an excellent job.

    ReplyDelete
  16. Ok...when y'all come to make me one?... Lol... Y'all did an excellent job.

    ReplyDelete
  17. Awesome idea, now to find someone to make me one of these, or better yet maybe even make it myself.

    Thanks for sharing!

    ReplyDelete
  18. I really love this idea, I feel like it would really work. I've got a lot of good ideas for my storage in Edmonton, I'd love to try. This seems like it would really work too, it's perfect!

    ReplyDelete
  19. Thanks for sharing this post. Storage racks are considered to be one of the most useful items available in the market and can be used for storing different kinds of commodities and equipments.

    Industrial storage racks manufacturers

    ReplyDelete
  20. I am looking for best RV storage facilities in Vancouver. Someone told me about RV storage in Vancouver, WA. I want your recommendations.

    ReplyDelete
  21. This is genius!!!! Found this on Pinterest! Please come share this on a party I cohost, DIY Sunday Showcase!

    Shelly
    minettesmaze.blogspot.com

    ReplyDelete
  22. Thanks a lot for sharing your create ideas with us and you have good collections in it. These Storage racks can hold multiple storage items, so that it provides spacious look to your place. Since these storage racks are compact and i hope it is easy to relocate to another place. Storage Rack Manufacturer.

    ReplyDelete
  23. Used storage racks is a great way to take advantage of these features, as well as the finacial benefits of purchasing used materials.

    Warehouse Storage Racks

    ReplyDelete
  24. Could pallets be modified to have it be similar to the same idea?

    ReplyDelete
  25. I love this! I hope to copy it soon! Thanks!

    ReplyDelete
  26. Now I just need the ability to chop, saw etc the bits.

    ReplyDelete
  27. Great Idea, I have just shared this on WeirdWood Facebook page hope you don't mind :-)

    https://www.facebook.com/WeirdWood

    ReplyDelete
  28. Hey! Nice can rack! My gf emailed me the link to it a few weeks ago. When I saw it it immediately presented the solution to my can storage issue and allowed me to use otherwise dead space productively.
    I built mine as a single unit, 5 slots wide, 2 slots high. It will hole 120 average size progresso soup cans. I tucked it into a 6' space I had behind the swing area of a door in my pantry. Worked out beautifully!
    I've never "blogged" before.. So I don't know how to share a picture of the one I built with you.. lol.. But if you're interested in seeing mine, just email me and I can send a shot of it in a reply.
    Thanks for the AWESOME inspiration!

    ReplyDelete
  29. Ok.. I figured out a way after all.. lol

    https://www.facebook.com/photo.php?fbid=10202949780686971&set=a.1625757565293.79833.1277131322&type=1&theater

    ReplyDelete
  30. Is there any reason the angle piece for the bottom couldn't be left whole rather than cutting it into the 2-3" pieces?

    ReplyDelete
  31. The cleats on the wall and the back of the can rack are referred to as a 'French Cleat', commonly used to hang wall cabinets.

    Nicely executed project.

    ReplyDelete
  32. What a nifty design! I need my hubby to build one of those.

    ReplyDelete
  33. Love the idea....but also have possible decorative idea for front of it . If going to use thinner wood for front y not buy just piece of latticework to go on front as u dont need to see can that much only enough to count them to see wht u need..let me know what you think. ...

    ReplyDelete
  34. I think this is a good idea, but I would suggest making it a little taller, because I see that you can only fit 9 cans in the row and if you buy by the case you get at least 12 cans in the case.

    ReplyDelete
  35. This is an awesome storage rack!!
    I love it!

    In my personal opinion, I think you are better off using 1x2s as opposed to using anything thinner...
    within reason, you can never have too much support....you8 can have to little, but not too much...within reason.
    This is an aawesome rack! TY for sharing. :)

    ReplyDelete
  36. I was just curious why you used a French cleat? Are the racks screwed into them or just hanging from them?

    ReplyDelete
    Replies
    1. The racks are screwed into them. We just uses them because we had seen them on home improvement shows and heard they are stronger.

      Delete
  37. omgosh.. this is amazing.. love that it keeps a nice rotation going and saves space ☺ Now.. I must see if the hubs will build it for me, cause I know how much he appreciates me in his garage.. lol

    ReplyDelete
  38. Pretty nifty!!! I'm not inspired to make one but my fella sure will. : P

    ReplyDelete
  39. This is great.I'm Going to build some real soon.my wife will be happy as all get out just to have more room in the pantry.

    ReplyDelete
  40. Oh my goodness! What a commendable work you have done, Keep up the great work mate success ll definitely follows you.

    Also visit best and affordable Funeral Homes Website Design.

    ReplyDelete
  41. Looks like you are no longer maintaining your blog. It's a pity. But on Pinterest this post of yours still flies around. We found it so interesting, that we built our own canned food storage!
    We even started our own blog and put a post on it about how we built our canned food storage, inspired by yours: https://famadiy.com/platzsparendes-diy-dosenregal
    Of course we gave credits to you :)

    Thanks for that nice inspiration!

    ReplyDelete
  42. Hi! I love you work. Maybe you can also use Eco Pipes in the future.

    ReplyDelete
  43. So what did the angle on the triangle with the L hook end up being? 45* ?

    ReplyDelete
  44. We bring authentic hairstyles for kids that have been introduced by the famous hairstylists around the world. So, you don’t really need to worry at all about whether or not your kid will be able to make a statement. https://www.mrkidshaircuts.com/kids-cool-haircuts/
    We also provide you with pertinent information about which trends from the past are making a comeback so that you can keep up with them. In short, if you want one resource as a solution for your little one’s hair, you should definitely check out Mr Kids haircuts.

    ReplyDelete
  45. I will build a DIY storage racks for my betta fish and I will used a wooden recycled pallets

    ReplyDelete